Type 25 Rear Bumper Bundle Kit - Black

Washer 8.4x16x1.6
Washer pushrod tube guard to head water boxer – T25
Washer front to rear hose brackets – T25 8/85>
Washer water pump pulley – T25 >7/85
Washer elbow clamps waterboxer – T25 >7/85
Washer exhaust to head waterboxer – T25 all years
Washer silencer clamp to down pipe diesel CS/KY – T25 >89
Washer silencer mounts diesel – T25
Washer steering column to couplings – T25
Washer clamp front gear shift rod to universal joint – T25 83>
Washer front & rear bumper mount centre section – T25
Washer body end of gas strut – T25
Washer upper roller sliding door – T25 85>
Washer fuel tank strap – Mk1 Golf
Washer small bumper iron rear to body cabrio clipper – Golf Cabrio 88>
Washer for cylinder block/ toothed belt guard 2.4/2.5 – T4
Washer for accelerator pedal and clutch assy – T1 Beetle
Washer for top header catch – T1 Cabriolet
Washer used in exhaust assemble for diesel engines – Mk2 Golf/Jetta

Replacement rear bumper in black primer for all 1979 to 1992 Type 25 Buses.

Please note that due to the length of this product an extra £5.00 will be charged if you would like it delivered.

Applications

VW Bus Rear Bumper

Type 25 bumper end cap for all models from 1979 to 1992.

This cap fits the front bumper on the left hand side and the rear bumper on the right hand side.

Type 25 bumper end cap for all models from 1979 to 1992.

This cap fits the front bumper on the right hand side and the rear bumper on the left hand side.

This fitting kit allows you to attach 1 bumper end cap onto a Type 25 Bumper.

Kit includes:

• 1 coach bolt with washer and nut
• 1 plastic clip
• 1 black plastic cap
• long self tapping screw or bolt.

Black bumper bolt cap to fit all Baywindow buses from August 1972 to the end of production and all Type 25 or T3 buses  

Quality: Top quality reproduction

Quantity: Sold each 

Fitting: Soften in hot water before installation so they constrict around the bolt head as they cool down and avoid splitting

Applications:

VW Baywindow Van: 1973 – 1979

VW Type 25 or T3: 1979 – 1992

This 8mm Bolt is 16mm long, with a 13mm head and a 1.25mm thread pitch.  it has a tensile strength of 8.8.  It can be used for various applications including:

• 200mm, 210mm and 228mm (T1) clutch to flywheel bolt
• T1 and 1302 steering column clamp bolt
• T2 1.7-2.0L clutch to flywheel bolt (200,210,228mm)
• T2 68-72 new bumper irons to new rear bumpers with plate fixings bolt
• T2 73-79 front bumper to deformation panel bolt
• T2 under floor plate bolt
  T2 -67 clutch to flywheel bolt
• T25 Waterboxer pushrod tube guard bolt
• T25 85-92 rear of cross pipe bracket bolt
• T25 anti roll bar bracket front suspension bolt
• T25 83-92 gear shift shaft flange supporting front bush bolt
• T25 front & rear bumper mount centre section bolt
• T25 cab door hinge to body bolt
• T25 79-84 centre hinge to sliding door bolt
• T25 carrier arm to front edge sliding door & lower roller mounting bolt

Fully Threaded Bolt (Set Screw)