**NCA** Beetle Stainless Steel Sidewinder Exhaust System (Also Fits Splitscreen Bus)

This 8mm full nut has a 1.25mm thread pitch and a 13mm head.  It can be used for various applications including:

• T1 general use nut
• 1303 74-79 ball joint clamp nut (chassis 134 2000 001)
• T1 68-79 rear anti roll bar bracket nut
• T2 Front beam steering stop nut
• T2 68-79 brake pedal to lever arm nut
• T2 68-72 bumper bolt nut
• T2 68-79 sliding door centre hinge cam nut
• T2 -67 general use nut
• T25 1600cc (CT) rocker shaft mounting block nut
• T25 camshaft pillars cylinder head nut (diesel)
• T25 silencer mount nut (diesel)
• T25 gear shift shaft plate nut
• T25 83-92 front gear shift rod to universal joint clamp nut
• T25 79-84 Nut above operating cam centre hinge sliding door
• Mark 1 Golf bumper iron nut (to metal bumper)

Stainless Steel Sidewinder exhaust header that fits Sidewinder muffler AC251707, sold separately for 1300cc – 1600cc Type 1 aircooled engines

Quality: Good quality

Quantity: HEADER ONLY

Fitment: Not for use with heat exchangers or preheats.

Not suitable for Baywindow vans as will not clear the engine brace bar.

Measurements: 41mm OD, 39mm ID

Applications:

VW Beetle: 1960 – 1979

VW Splitscreen Van: 1960 – 1967

VW Karmann Ghia: 1960 – 1974

VW Buggy + Baja: 1960 – 1979

This stainless steel exhaust muffler can be used on all VW Beetles and Karmann Ghia`s with the correct Sidewinder header fitted (Sold Separately).

The Sidewinder exhaust will not fit Baywindow buses because it will foul on the rear engine brace.

It will however fit Splitscreen Buses but a little modification to the rear valance maybe required.

Tailpipe Outer Diameter 63.4mm

Tailpipe Inner Diameter – 61.7mm

Flange outer Diameter – 48.7mm

Flange Inner Diameter – 47.2mm

This 8mm Bolt is 16mm long, with a 13mm head and a 1.25mm thread pitch.  it has a tensile strength of 8.8.  It can be used for various applications including:

• 200mm, 210mm and 228mm (T1) clutch to flywheel bolt
• T1 and 1302 steering column clamp bolt
• T2 1.7-2.0L clutch to flywheel bolt (200,210,228mm)
• T2 68-72 new bumper irons to new rear bumpers with plate fixings bolt
• T2 73-79 front bumper to deformation panel bolt
• T2 under floor plate bolt
  T2 -67 clutch to flywheel bolt
• T25 Waterboxer pushrod tube guard bolt
• T25 85-92 rear of cross pipe bracket bolt
• T25 anti roll bar bracket front suspension bolt
• T25 83-92 gear shift shaft flange supporting front bush bolt
• T25 front & rear bumper mount centre section bolt
• T25 cab door hinge to body bolt
• T25 79-84 centre hinge to sliding door bolt
• T25 carrier arm to front edge sliding door & lower roller mounting bolt

Fully Threaded Bolt (Set Screw)

This 8mm hex head bolt is 35mm long, with a 13mm head and a 1.25mm thread pitch.  it has a tensile strength of 8.8.  It can be used for various applications including:

• T1 Blade Bumper Overider Bolt