Type 1 Stainless Steel Mondo Exhaust System

This 8mm full nut has a 1.25mm thread pitch and a 13mm head.  It can be used for various applications including:

• T1 general use nut
• 1303 74-79 ball joint clamp nut (chassis 134 2000 001)
• T1 68-79 rear anti roll bar bracket nut
• T2 Front beam steering stop nut
• T2 68-79 brake pedal to lever arm nut
• T2 68-72 bumper bolt nut
• T2 68-79 sliding door centre hinge cam nut
• T2 -67 general use nut
• T25 1600cc (CT) rocker shaft mounting block nut
• T25 camshaft pillars cylinder head nut (diesel)
• T25 silencer mount nut (diesel)
• T25 gear shift shaft plate nut
• T25 83-92 front gear shift rod to universal joint clamp nut
• T25 79-84 Nut above operating cam centre hinge sliding door
• Mark 1 Golf bumper iron nut (to metal bumper)

Replacment stainless steel 4 into 1 small flange header for stainless steel single quiet pack part number AC251713 ONLY

This will NOT fit other mufflers due to the angle of the flange.

Quality: Top quality

Quantity: Header only

Fitment: Type 1 1300cc – 1600cc engines

Fitting: Supplied with gaskets

Applications:

VW Beetle: 1960 – 1979

VW Splitscreen Van: 1960 – 1967

VW Baywindow Van: 1968 – 1979

VW Karmann Ghia: 1960 – 1974

VW Trekker: 1968 – 1983

VW Buggy + Baja: 1960 – 1979

Stainless Steel Mondo Muffler For 4 into 1 Header.

NOT SUITABLE FOR BAY WINDOW VANS

This 8mm bolt is 20mm long, it has a 13mm head and has a 1.25mm thread pitch.  This bolt has a tensile strength of 8.8.  It is used for various applications including:

• T2 rear wheel cylinder to backing plate bolt
• T25 silencer mount bolt (diesel models)
• Mark 1 Golf bumper iron (metal bumper) to body bolt

Fully Threaded Bolt (Set Screw)

Aluminium corrugted air hose fitted from the fanshroud to the heat exchanger on Type 1, 1200cc – 1600cc engines.

Also can be used where any 50mm ID air hose is required.

Quality: Top quality

Quantity: Sold each, 2 required per engine

Measurements: 500mm x 50mm

Fitting: 1 x 500mm is only long enough to fit one side of the fan shroud to heat exhanger, 2 required per engine, 3 if you have the pre heat hose installed that runs from the air filter housing to the tin over exhaust

Applications:

VW Beetle: 1960 – 1979

VW Splitscreen Van: 1960 – 1967

VW Baywindow Van: 1968 – 1979

VW Karmann Ghia: 1960 – 1974

VW Type 3: 1961 – 1973

VW Trekker: 1968 – 1983

VW Buggy + Baja: 1960 – 1979

Jubilee style clip 40-60mm

Complete exhaust to engine fitting kit includes all clamps, screws and gaskets for use on all aircooled Volkswagen engines from 1960 onwards including 1200cc, 1300cc, 1500cc and 1600cc models

Please note dual hotspot engines will require additional pre heat pipe gaskets, 2 x 113251263D

Quality: Good quality reproduction

Fitting: If you require tailipe clamps, see part number 111298051BBT

Fitment: Not suitable for 1700cc, 1800cc or 2000cc Type 4 engines or 25HP and 30HP engines manufactured before 1960

Applications:

VW Beetle: 1960 – 1979

VW Splitscreen Van: 1960 – 1967

VW Baywindow Van: 1968 – 1979

VW Karmann Ghia: 1960 – 1974

VW Type 3: 1961 – 1973

VW Trekker: 1968 – 1983

VW Buggy + Baja: 1960 – 1979